TDS – AwlGrip Awlcraft SE Topcoat

Surface Preparation

Awlcraft SE basecoats should be applied over the appropriate Awlgrip primer or previous Awlgrip / Awlcraft topcoat. The primed surface must be clean and dry. Wipe with Surface Cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method. Achieving maximum gloss and distinction of image requires the primer and/or existing topcoat be smooth sanded with P400 grit paper before application. The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.

Mixing & Reduction
Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended.
                                     

Mix to a smooth, homogenous mixture. Awlcraft SE basecoats are designed for spray application only and have a significantly shorter pot life than regular topcoats. DO NOT add accelerators to Awlcraft SE.

Application

Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary.
Apply first crosscoat using a smooth, even and fluid spray application technique in order to achieve a uniform, consistent finish. Apply no more than 25-35cm (1014”) width areas at a time. Constant air pressure is necessary during application to ensure evenness of finish. Allow to flash off until surface is matt (~10mins at 25°C/77°F).
Apply second crosscoat in the same way as the first.
When applying a metallic or a 2-stage pearlescent color, an optional dropcoat (mistcoat) can be applied prior to clear coating. This may be necessary to
ensure consistency in metallic flake orientation and can be applied whilst previous crosscoat is wet or once surface is matt. The dropcoat will help to achieve a consistent finish and avoid shade variations and/or clouding. When applying a 3-stage pearlescent color, it is important to achieve opacity with the solid basecoat. This is normally achieved in 2-3 coats. Once opacity has been achieved, the pearl mid-coat can be applied in 1-2 coats. Care must be taken to ensure an even film of mid-coat is applied as overlaps, or additional coats, can alter the final shade of the topcoat.
For solid color basecoats, apply smooth wet coats until opacity has been achieved. Most colors require 1-2 coats; however some colors may require
additional coats. Once the surface has gone completely matt apply 2 full coats of Awlcraft 2000 Clear or Awlgrip HDT Clear. After applying the specified basecoat color, allow the coating to cure a minimum of 1 hour at 25°C (77°F) and up to 3 days before clear applications. See application and mixing instructions on the Clear Coat Technical Data Sheet.
DO NOT add accelerators to Awlcraft SE.
Awlcraft SE is designed for spray application only.
Awlcraft SE must be clear coated.
Surface/Ambient temperature range is 2332°
C (7090° F). Proper application and/or cure results may be more difficult to achieve when conditions are outside this range. Do not apply paint materials to surfaces less than 3°C (5°F) above dew point, or to surfaces warmer than 41°C (105°F). Ambient temperature should be minimum 10°C (50°F) and maximum 41°C (105°F).

Recoatability & Drying Times
The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, consult your local technical service representative before proceeding.

Overcoated By: Awlcraft 2000, Awlgrip HDT Clearcoat 
Temp: (95°F) 60 Minutes Min, 3 days MAX 
Temp: 25°C (77°F) 60 Minutes Min, 3 days MAX
Awlcraft SE Basecoat surface must be kept clean at all time before clearcoat application. To reduce dust contamination, clean compressed air or tack rags should be used over Awlcraft SE Basecoat. Oil contamination should be removed using light amounts of Awlgrip Wipe Down Solvent (NA/AP: Awlprep T0008; EU: Surface Cleaner T0340). In case of heavy contamination contact your local Representative.

Specification Data
Volume Solids 22%
Available Packs 1 US Quart, 1 US Gallon
Base L-Code (Awlcraft SE Solid Basecoat)
E-Code (Awlcraft SE Metallic Basecoat)
P-Code (Awlcraft SE Pearlescent Basecoat)
S-Code (Awlcraft SE Solids, Pearls, Matallic Basecoats)
Converter:  G3010 - Awl Cat #2 Spray Converter
Reducer(s):

• T0001 - Fast Evaporating Reducer-Spray
• T0003 - Standard Reducer-Spray
• T0005 - Hot Weather Reducer-Spray

Equipment Cleaning T0001, T0002, T0003
Typical Shelf Life 3 years

Mix Ratio (Spray Only): Mix by volume 100 Parts of Awlcraft SE Topcoat Base Component with 50 Parts Reducer (T0001, T0003 or T0005 sold separately) and with 15 Parts Awlcat #2 G3010 Spray Converter (sold separately). Mix to a smooth, homogeneous mixture. Awlcraft SE basecoats are designed for spray application only and have a significantly shorter pot life than regular topcoats. Do not add accelerators to Awlcraft SE.

List of White Awlcraft SE Green Colors:

TDS – AwlGrip Awlcraft SE Topcoat

Surface Preparation

Awlcraft SE basecoats should be applied over the appropriate Awlgrip primer or previous Awlgrip / Awlcraft topcoat. The primed surface must be clean and dry. Wipe with Surface Cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method. Achieving maximum gloss and distinction of image
requires the primer and/or existing topcoat be smooth sanded with P400 grit paper before application. The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.

Mixing & Reduction
Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended.
                                     

Mix to a smooth, homogenous mixture. Awlcraft SE basecoats are designed for spray application only and have a significantly shorter pot life than regular
topcoats. DO NOT add accelerators to Awlcraft SE.

Application

Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and
other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further
advice if necessary.
Apply first crosscoat using a smooth, even and fluid spray application technique in order to achieve a uniform, consistent finish. Apply no more than 25-35cm (1014”)
width areas at a time. Constant air pressure is necessary during application to ensure evenness of finish. Allow to flash off until surface is matt
(~10mins at 25°C/77°F).
Apply second crosscoat in the same way as the first.
When applying a metallic or a 2-stage pearlescent color, an optional dropcoat (mistcoat) can be applied prior to clear coating. This may be necessary to
ensure consistency in metallic flake orientation and can be applied whilst previous crosscoat is wet or once surface is matt. The dropcoat will help to achieve
a consistent finish and avoid shade variations and/or clouding.
When applying a 3-stage pearlescent color, it is important to achieve opacity with the solid basecoat. This is normally achieved in 2-3 coats. Once opacity
has been achieved, the pearl mid-coat can be applied in 1-2 coats. Care must be taken to ensure an even film of mid-coat is applied as overlaps, or additional
coats, can alter the final shade of the topcoat.
For solid color basecoats, apply smooth wet coats until opacity has been achieved. Most colors require 1-2 coats; however some colors may require
additional coats.
Once the surface has gone completely matt apply 2 full coats of Awlcraft 2000 Clear or Awlgrip HDT Clear. After applying the specified basecoat color, allow
the coating to cure a minimum of 1 hour at 25°C (77°F) and up to 3 days before clear applications. See application and mixing instructions on the Clear Coat
Technical Data Sheet.
DO NOT add accelerators to Awlcraft SE.
Awlcraft SE is designed for spray application only.
Awlcraft SE must be clear coated.
Surface/Ambient temperature range is 2332°
C (7090° F). Proper application and/or cure results may be more difficult to achieve when conditions are outside
this range. Do not apply paint materials to surfaces less than 3°C (5°F) above dew point, or to surfaces warmer than 41°C (105°F).
Ambient temperature should be minimum 10°C (50°F) and maximum 41°C (105°F).

Recoatability & Drying Times
The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, consult
your local technical service representative before proceeding.

Overcoated By: Awlcraft 2000, Awlgrip HDT Clearcoat 
Temp: (95°F) 60 Minutes Min, 3 days MAX 
Temp: 25°C (77°F) 60 Minutes Min, 3 days MAX
Awlcraft SE Basecoat surface must be kept clean at all time before clearcoat application. To reduce dust contamination, clean compressed air or tack rags should be used over Awlcraft SE Basecoat. Oil contamination should be removed using light amounts of Awlgrip Wipe Down Solvent (NA/AP: Awlprep T0008; EU: Surface Cleaner T0340). In case of heavy contamination contact your local Representative.