AwlGrip 3000 Clear Coat TF0300 Technical Data Sheet  

Specifications Data

Volume Solids: 44.3% unthinned
Specific Gravity: 0.99
Available Packs: 1 US Quart, 1 US Gallon
Base: TF0300
Converter: Awlcat #2 (G3010)
Reducer
T0001 - Fast Evaporating Reducer-Spray
T0002 - Very Fast Evaporating Reducer-Spray
T0003 - Standard Reducer-Spray
T0005 - Hot Weather Reducer - Spray
Equipment Cleaning: T0001, T0002, T0003
Typical Shelf Life: Base - 3 years, Converter - 1 Year

Theoretical Coverage Application

Methods: Air Atomized
Number of Coats: 3
Recommended Per Coat:
WFT: 75 µm (3 mil)
DFT:  33 µm (1.3 mil) 
Max DFT: N/A
Theoretical Coverage Per Coat (at recommended DFT):  13.1 m²/lt 533.7 ft²/Gal

NOTE: Coverage calculations are based on a theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, thinning, application techniques, part size, and application environment.

Surface Preparation

The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition, and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.

For the application of the basecoat please refer to the Awlcraft SE TDS.
Awlcraft 3000 Clearcoat should be applied over Awlcraft SE Basecoat. Awlcraft SE Basecoat surface must be kept clean at all times before Awlcraft 3000 Clearcoat application. See Awlcraft SE Technical Datasheet for recommendations.
Over Awlcraft 2000 & Awlcraft 3000 topcoat sand with P400 to remove the gloss and clean with Surface Cleaner T0170 (US/AP) or T0340 (EU) using the two cloth wipe-down method.

Do not use unless mixed thoroughly with the curing agent at specified ratio. Avoid painting in direct sunlight. Do not apply paint materials to surfaces less than 5°F (3°C) above dew point, or to surfaces warmer than 105°F (41°C). Ambient temperature should be minimum 55°F (13°C) and maximum 105°F (41°C). At standard conditions (77˚F (25˚C), 50% R.H.), avoid applying topcoats when the temperature could drop below the dew point within 6–8 hours after the application.

Mixing and Reduction

Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended.

Mix by volume two parts Awlcraft 3000 Clearcoat Base with one part Awlcat #2 (G3010) Spray Converter to a smooth, homogenous mixture. Reducer addition level required to achieve 11-15 seconds viscosity DIN4 or equivalent (16-18 seconds viscosity Zahn 2) varies color to color.. For standard air atomized application this can be attained by adding up to 33% reducer, using the correct spray reducer appropriate for conditions.

For example, if a 25% reduction is used, overall mix is 2:1:¾ by volume (8 oz. Base, 4 oz. G3010, 3 oz. Reducer or 2L Base, 1L G3010, 0.75L Reducer).

Application

Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary.

Apply a smooth, wet coat to the surface. Allow coat to "flash off" 15–45 minutes. Then apply a full, wet coat to achieve color coverage and film thickness requirements. Allow the second coat to "flash off" 30–45 minutes until only slightly tacky before applying a third coat. For best results, coats two and three should be applied wet for the paint film to fully coalesce and level. However, take care not to overapply which could lead to sagging of the topcoat. For specific equipment setups, please contact your local technical sales representative, the equipment manufacturer or your distributor.

Recoatability & Drying Times

The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, consult your local technical service representative before proceeding. Typical spray applications consist of three coats applied over 1-4 hours. Exact time will vary with temperature, project size, and film thickness applied. Awlcraft 3000 Clearcoat topcoats which have been allowed to cure more than 24 hours must be sanded before recoating.

For specific recoatability and drying times check the Technical Data Sheet (TF0300)

Warning Notes

The information in this Product Data Sheet is not intended to be exhaustive. Any person using the product without first making further enquiries as to the suitability of the product for the intended purpose does so at their own risk and, to the extent permitted by law, we can accept no responsibility for the performance of the product or for any loss or damage arising out of such use. The information contained in this Product Data Sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.