Warning: Undefined array key 1 in /home/bottompt/oc4.bottompaintstore.com/catalog/controller/startup/seo_url.php on line 84Warning: Undefined array key 1 in /home/bottompt/oc4.bottompaintstore.com/catalog/controller/startup/seo_url.php on line 84Warning: Undefined array key 1 in /home/bottompt/oc4.bottompaintstore.com/catalog/controller/startup/seo_url.php on line 84 Flexdel Bottom Gard Bottom Paint

My cart

0 item(s) - $0.00

  • Your shopping cart is empty!

Flexdel Bottom Gard Bottom Paint
Flexdel Bottom Gard Bottom Paint
Flexdel Bottom Gard Bottom Paint

Flexdel Bottom Gard Bottom Paint

$89.88
Brand:
Product Code: Bottom Gard
Stock In Stock

Available Options

Product Description

Bottom Gard is an ablative, antifouling bottom paint for fiberglass and wooden boats. Flexdel Bottom Gard Bottom Paint features a solvent-based ablative technology that repels barnacles and other marine growth. At an extremely economical price, Bottom Gard is an exceptional value with outstanding performance. Easy to apply and evenly coat. Bottom Gard can be applied over existing bottom paints that are clean, free of any debris, and dry.

  • Please note the states this product can ship to below before ordering.
  • Ablative action repels barnacles & other growth
  • Outstanding value & great performance
  • U.S. EPA approved
  • 25% Copper
  • Colors: Black, Red, and Blue

*This Item Ships From Florida 

Click to See Transit Times

Please Note: This item is only available to ship to the following states: North Carolina, New Hampshire, New Jersey, New York, Rhode Island, Florida, and Virginia.

Size Chart
Application Method: Brush or Roller
Number of Coats: 1-2 (Additional coat at waterline)
Coverage: 400 sq. ft./gal.
Dry Times:
  Application Temp:    Re-coat (hours)    To Launch (hours) 
50°F                                     4                                 24 
70°F                                     2                                 18
90°F                                     1                                 16
 **Above times are minimum
 
Surface Preparation
 
Painted Bottom
If the paint on the bottom of your boat is flaking, you should get a scraper and remove all loose flakes.
If the paint on the bottom of your boat is in poor condition, consider using a paint stripper and removing the old layer completely.
Remember: The adhesion of the new paint is only as good as the paint it is being applied over. Watch for signs of adhesion failure.
If your bottom paint is in good condition, you only need to sand it a little with 80-grit sandpaper, clean it up, tape it off and roll on another coat.
Bare Aluminum
Clean the hull surface thoroughly with de-waxing solvent and plenty of clean rags.
Sand the de-waxed hull lightly with 80-grit paper.
Wipe down the area again to remove all sanding residue.
Apply 190 Primer. Follow the manufacturer’s recommendations for primer application.
 
Application Procedure:
Mixing the Paint
Take the time and effort to properly mix your paint. If the copper isn’t evenly distributed, some areas of your hull will not be protected.
If you have a paint shaker, run it for at least 5 minutes to get the copper and pigment evenly distributed.
If you are mixing by hand, keep dredging up the copper off the bottom of the can.
Each time you add to your roller tray you will want to stir again to ensure consistency.
Applying the Paint
Fill your paint tray with paint and dip your roller. Roll the paint onto the hull using a short-nap roller cover (usually 3/8 nap).
Note: Don’t add any thinner to the bottom paint unless the manufacturer specifies otherwise. Stir the paint before refilling the paint tray.
By the time you work all the way around the hull, many bottom paints will be dry enough to overcoat.
A second coat is usually recommended and will increase the life of almost any bottom paint; copolymers benefit from 3 or 4 coats.
No sanding or other prep is needed between coats.
Caution: Be sure you leave all zinc anodes unpainted. If you are installing new zincs, make sure you do not paint over their mounting locations. Good electrical contact is essential for zincs to do their job.

Finish: Flat
Coverage: 400 sq. ft./gal.
Number of Coats: 1-2
Application Method: Brush or roller
Colors Available: 60101 Black, 60102 Red, 60103 Blue
VOC: 508 grams per liter

So Extra Slider: Has no item to show!
Flexdel Bottom Gard Bottom Paint

Flexdel Bottom Gard Bottom Paint

$89.88