Column Left Debug: 0
Interdeck Nonskid Deck Paint
Product Description
Interdeck Non-Skid Finish – A tough, slip resistant deck paint that protects the surface from every day wear and tear. It’s easy to apply, comes in a range of colours and its low sheen finish helps prevent sunlight from reflecting off decks.
Key Features:
- Slip-resistant deck paint that’s suitable for all substrates
- Contains fine mineral additive for hard wearing, non-slip surface
- Low sheen finish prevents sunlight dazzle
Interdeck* provides an excellent slip resistant finish. It contains a fine aggregate and will apply easily on all substrates. * Low sheen finish prevents dazzling reflected sunlight off decks * Easy application * Available in a range of colours The tough polyurethane resin protects decks against everyday wear and tear.
*This Item Ships From South Florida Click to See Estimated Transit Times
PREPARATION:
BARE FIBERGLASS: In Good Condition - Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water and allow to dry. Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned. Sand using 180-220 grade (grit) paper. Remove sanding residue.
MOLDED IN NON-SKID SURFACES - Scrub with Fiberglass Surface Prep YMA601 or Solvent Wash 202V using a 3M Doodlebug™and a maroon Scotch-Brite ® pad. Rinse with fresh water.
PREVIOUSLY PAINTED SURFACES:
In Good Condition – The surface must be clean and dry. Sand with 220-320 grade (grit) paper. Remove sanding residue.
In Poor Condition – Remove all previous coatings and prime the substrate.
BARE WOOD: Sand surface, wipe clean. Apply Prekote Primer. Sand surface, wipe clean.
METAL: Use Interprotect 2000E to prime the surface of the prepared metal. See the Interprotect 2000E Technical Datasheet for bare metal preparation guidelines.
CLEAR EPOXY: Clean as for Bare Fiberglass above. Sand with 80 grade (grit) paper. Remove sanding residue. Apply one coat of Epoxy Barrier-Kote 404/414.
APPLICATION: Sand the primer with 180-220 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.
Mixing: Stir well before use.
Thinner: Brushing Liquid 333 Cleaner Special Thinner 216.
Ventilation and Humidity Control: Apply in dry, well ventilated conditions.
TIPS: For best results either stipple by brush or use a mohair roller.
**IMPORTANT: Product temperature should be minimum 10°C/50°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F.
Color: YJB000 – White
Finish: Low Sheen
Specific Gravity: 1.4
Volume Solids: 54%
Typical Shelf Life: 2yrs
VOC (As Supplied): 357 g/lt
Dry and Overcoat Times: See Technical Data Sheet
Application Methods: Brush, Roller
Recommended DFT per coat: 2 mils dry
Recommended WFT per coat: 3.7 mils wet
Coverage: (Theoretical) 386.7 ft²/gal
Number of Coats: 1-2 coats
Storage and Handling: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Interdeck* to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
Related Products
Interlux Brushing Liquid 333
Interlux Special Thinner 216
