Column Left Debug: 0
Blue Water Marine Mega Gloss Polyurethane Quart
Product Description
Mega Gloss - The New Science of Polyurethane Finishes - Polyurethane Topside Enamel
Mega GlossTM is a technically advanced, single component topside polyurethane enamel giving you a hard protective coating for super high gloss, color retention, and long durability. Mega Gloss is fast drying which when brushed or rolled gives a smooth finish with excellent handle and flow. This widely used topside polyurethane enamel has tremendous resistance to tough chemicals, cleaning solutions and ultraviolet light with its advanced ultraviolet technology. Can be used on fiberglass, wood, aluminum and steel. It's like wrapping your boat in glass!
- Super High Gloss
- Smooth Finish
- Excellent Handle & Flow
- Superior UV Protection Prevents Fading
- Resistance to Tough Chemicals
- Fiberglass, Steel, Aluminum,Wood
- Excellent Recoatability
- Tremendous Coverage & Hiding
Click Here > Blue Water Marine Mega Gloss Polyurethane Technical Data Sheet
Click Here > Blue Water Marine Mega Gloss Polyurethane MSDS
*This Item Ships From Florida Click to See Estimated Transit Times
Suggested Uses: Topside, Decks, Cabin, Masts, Bilge, Waterline, Boot top Striping
Application: Brush, Spray, or Roller
Primer: Mega Gloss Primer
Primer for Aluminum: While Mega Gloss Primer can be used, for pitting or water barrier option is Bottom Protect Primer by Blue Water. Thin first coat 20% (spray Thinner 975/roll or brush thinner 974 or 976), apply a second coat, let fully cure then paint.
Surface Preparation: Water blast surface to remove all loose paint, dirt, oils, and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipes down to remove all sanding residue. Prime with Mega Gloss Primer for best results.
Spray: Conventional Air Gravity Feed 59-70 psi, Tip Size .055 -.070, Airless 2200-2500 psi, Tip Size .013-.017. The product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with enamel reducer (Xylene.).
Roll: 1/2” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. The product can be reduced as needed with Hi Flash Naphtha to allow proper flow out and performance.
Limitations: Do not apply if material, substrate or ambient temperature is
below 50°F or above 95°F.
Finish: Gloss
Vehicle Type: Polyurethane Alkyd Resin
Solvent Type: High Flash Naphtha
VOC: 3.76 lbs. / gal (450 grams / liter)
Solids By Weight: 50%
Weight Per Gallon: 10 lbs. per gallon (varies by color)
Recommended Dry Film: 4.0 mils
Coverage: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
Viscosity At 75°F (24°C): 70-80 KU
Average Dry Time 75°F: Dries to touch in 4 hours. Lower temperatures & higher humidity will slow down dry times.
Recommended Reducer: Xylene for spray application, Hi Flash Naphtha for brushing or rolling
Resistance To: Chemical Resistance, Abrasion, Oils, Grease, Rust, Corrosion,
Mildew, Chipping and Fading
Recommended Primers:
Pot Life: Not Applicable
Shelf Life: Maximum 12 months
Mixing: Mechanically mix for 10 minutes, making sure that all solid material is mixed thoroughly.
Cleanup: Xylene for Equipment.
